% systematic delays important to obtain the best synchronisation
The beacon synchronisation strategy hinges on the ability to measure the beacon signal with sufficient timing accuracy.
In the previous chapters, the overall performance of this strategy has been explored by using simulated waveforms.
\\
% ADC and filtering setup most important component.
As mentioned in Chapter~\ref{sec:waveform}, the measured waveforms of a true detector will be influenced by characteristics of the antenna, the filter and the \gls{ADC}.
Especially the filter and \gls{ADC} are important components to be characterised to compensate for possible systematic (relative) delays.
%The \gls{DU} timestamps an event using a combination of the 1\gls{PPS} of a Trimble ICM 360 \gls{GNSS} chip\Todo{ref?} and counting the local oscillator running at $500\MHz$.
%At trigger time, the counter value is stored to obtain a timing accuracy of roughly $2\ns$.
%The counter is also used to correct for fluctuating intervals of the 1\gls{PPS} by storing and resetting it at each incoming 1\gls{PPS}.
Two \gls{DU}-channels receive the same signal from a signal generator where one of the channels takes an extra time delay $\Delta t_\mathrm{cable}$ due to extra cable length.
In this ``forward'' setup, both channels are read out at the same time, and a time delay is derived from the channels' traces.
The sum of the ``forward'' and ``backward'' time delays gives twice the relative time delay $\Delta t$ without needing to measure the time delays due to the cable lengths $t_\mathrm{cable}$ separately since
The measured phase differences between channels 2 and 4 at $50\MHz$ converted to a time delay for the \subref{fig:grand:phaseshift:measurements:forward}~forward and \subref{fig:grand:phaseshift:measurements:backward}~backward setups.
The dashed vertical lines indicate the mean time delay, the errorbar at the bottom indicates the standard deviation of the samples.
Crosses are TD-triggered events, circles are MD-triggered.
The measurements are time-ordered within their trigger type.
Figure~\ref{fig:channel-delays} shows the measured total time delays and the resulting signal chain time delays between both channels 1 and 2, and channels 2 and 4.
Apart from two exceptional time delays upto $0.2\ns$, the signal chain time delays are in general below $0.05\ns$.
\\
Note that the reported signal chain time delays must be taken to be indications due to systematic behaviours (see below).
\\
Still, even when taking $0.2\ns$ as the upper limit of any relative signal chain time delay, the electric field at the antenna are reconstructable to a sufficient accuracy to use either the pulsed or sine beacon methods (see Figures~\ref{fig:pulse:snr_time_resolution} and~\ref{fig:sine:snr_time_resolution} for reference) to synchronise an array to enable radio interferometry.
\\
Note that at higher frequencies the phase differences are phase-wrapped due to contention of the used period and the cable time delay.
Because it is symmetric for both setups, this should not affect the measurement of the signal chain time delay at the considered frequencies.
Nevertheless, the result at these frequencies must be interpreted with some caution.
\\
% Discussion
The time delays for both TD- and MD-triggered events in Figure~\ref{fig:grand:phaseshift:measurements} show a systematic behaviour of increasing total time delays for the forward setup.
However, in the backward setup, this is not as noticable.
\\
This skewing of the channel time delays in one of the setups is also found at other frequencies (see Figures~\ref{fig:grand:phaseshift:ch1ch2} and~\ref{fig:grand:phaseshift:ch2ch4}), raising questions on the stability of the setup.
Unfortunately, it is primarily visible in the larger datasets which correspond to measurements over larger timescales.
As the number of these large datasets is limited, further investigation with the current datasets is prohibited.
\\
The skewing might also be an artifact of the short waveforms ($N\sim500\;\mathrm{samples}$) the data acquisition system was able to retrieve at the time of measurement.
Since the data acquisition system is now able to retrieve the maximum size waveforms, this systematic behaviour can be investigated in a further experiment.
Total (\textit{upper}) and signal chain (\textit{lower}) time delays between \subref{fig:channel-delays:1,2} channels 1 and 2, and \subref{fig:channel-delays:2,4} 2 and 4.
The dark grey vertical lines in the upper panes indicate the maximum measurable time delays at each frequency.
Due to systematic effects in the measurements and a low number of samples at certain frequencies, the signal chain time delays depicted here must be taken as indicative.
