Thesis: Radio Measurement Chapter to Harm

documents/thesis/chapters/radio_measurement.tex

@@ -25,39 +25,37 @@ Additionally, the shape and size of antennas affect how well the antenna respond
 %Waveform + Time vector,
 In each radio detector, the antenna presents its signals to an \gls{ADC} as fluctuating voltages.
 In turn, the \gls{ADC} records the analog signals with a specified samplerate $f_s$ resulting in a sequence of digitised voltages or waveform.
-In this waveform, the $n$-th sample is associated with a fixed timestamp $t_n = t_0 + n/f_s$ after the initial sample at $t_0$.
+The $n$-th sample in this waveform is then associated with a fixed timestamp $t[n] = t[0] + n/f_s = t[0] + n*\Delta t$ after the initial sample at $t[0]$.
+In reality, the sampling rate will vary by very small amounts resulting in timestamp inaccuracies called jitter.
 \\
 
 % Filtering before ADC
 The finite sampling rate of the waveform means that very high frequencies are not observed by the \gls{ADC}.
-However, frequencies just at or above half of sampling rate will affect the sampling and appear in the waveform at lower frequencies as aliases.
+However, frequencies just at or above half of sampling rate will affect the sampling itself and appear in the waveform at lower frequencies as aliases.
 This frequency at half the sampling rate is known as the Nyquist frequency.
 To prevent such aliases, these frequencies must be removed by a filter before sampling.
 \\
 For air shower radio detection, very low frequencies are also not of interest.
 Therefore, this filter is generally a bandpass filter.
-For example, in \gls{Auger} the filter removes all of the signal except for the frequency interval between $30 \text{--} 80\MHz$.\Todo{citation}
+For example, in \gls{Auger} the filter removes all of the signal except for the frequency interval between $30 \text{--} 80\MHz$.\Todo{citation?}
 \\
 In addition to a bandpass filter, more complex filter setups are used to remove unwanted components or introduce attenuation at specific frequencies.
-For example, in \gls{GRAND} notch filters are introduced to suppress radio signals in the FM-radio band which lies in its $20 \text{--} 200\MHz$ band.\Todo{citation}
+For example, in \gls{GRAND} notch filters are introduced to suppress radio signals in the FM-radio band which lies in its $20 \text{--} 200\MHz$ band.\Todo{citation?}
 \\
 
 % Filter and Antenna response
 From the above it is clear that the digitised waveform is a measurement of the electric field that is sequentially convoluted by the antenna's and filter's response.
 Thus to reconstruct properties of the electric field signal from the waveform, both responses must be known.
 
-\begin{figure}
-	\caption{Antenna arms of a GRAND detector, a noisy waveform and a filter response}
-\end{figure}
 
 % Analysis, properties, frequencies, pulse detection, shape matching,
 \bigskip
 Different methods are available for the analysis of the waveform, and the antenna and filter responses.
 A key aspect is determining the frequency-dependent amplitudes (and phases) in the measurements to characterise the responses and, more importantly, select signals from background.
 With \acrlong{FT}s these frequency spectra can be produced.
-This technique is especially important for the sine beacon of Section~\ref{sec:beacon:sine}, as it forms the basis of the phase measurement.
+This technique is especially important for the sinewave beacon of Section~\ref{sec:beacon:sine}, as it forms the basis of the phase measurement.
 \\
-The detection and identification of more complex signals can be achieved using the cross correlation\Todo{rephrase},
+The detection and identification of more complex time-domain signals can be achieved using the cross correlation\Todo{rephrase},
 which is the basis for the pulsed beacon method of Section~\ref{sec:beacon:pulse}.
 
 %\section{Analysis Methods}% <<<
@@ -67,13 +65,13 @@ which is the basis for the pulsed beacon method of Section~\ref{sec:beacon:pulse
 \section{Fourier Transform}% <<<<
 \label{sec:fourier}
 The \gls{FT} allows for a frequency-domain representation of a time-domain signal.
-In the case of radio antennas, it converts a time-ordered sequence of voltages into a complex amplitudes that depend on frequency.
+In the case of radio antennas, it converts a time-ordered sequence of voltages into a set of complex amplitudes that depend on frequency.
 By evaluating the \gls{FT} at appropriate frequencies, the frequency spectrum of a waveform is calculated.
 This method then allows to modify a signal by operating on its frequency components, i.e.~removing a narrow frequency band contamination within the signal.
 \\
 
 % DTFT from CTFT
-The continuous \gls{FT} takes the form
+The continuous \acrlong{FT} takes the form
 \begin{equation}
 	\label{eq:fourier}
 	\phantom{.}
@@ -106,36 +104,51 @@ where $x(t)$ is sampled a finite number of times $N$ at some timestamps $t[n]$.
 Note that the amplitude $A(f)$ will now scale with the number of samples~$N$, and thus should be normalised to $A(f) = 2 \left| X(f) \right| / N$.
 \\
 
-Considering a finite sampling size $N$ and periodicity of the signal, the bounds of the integral in \eqref{eq:fourier} have collapsed to $t[0]$ up to $t[N]$.
+Considering a finite sampling size $N$ and periodicity of the signal, the bounds of the integral in \eqref{eq:fourier} have collapsed to $t[0]$ up to $t_{N-1}$.
-It follows that the lowest resolvable frequency is $f_\mathrm{lower} = 1/T = 1/(t[N] - t[0])$.
+It follows that the lowest resolvable frequency is $f_\mathrm{lower} = 1/T = 1/(t_{N-1} - t[0])$.
 \\
 Additionally, when the sampling of $x(t)$ is equally spaced, the $t[n]$ terms can be written as a sequence, $t[n] - t[0] = n \Delta t = n/f_s$, with $f_s$ the sampling frequency.
 Here the highest resolvable frequency is limited by the Nyquist~frequency at $f_\mathrm{nyquist} = f_s/2$.
 \\
 
 % DFT sampling of DTFT / efficient multifrequency FFT
-Implementing the above decomposition of $t[n]$, \eqref{eq:fourier:dtft} can be rewritten in terms of multiples of the sampling frequency $k = f/f_s$, becoming the \gls{DFT}
+Implementing the above decomposition of $t[n]$, \eqref{eq:fourier:dtft} can be rewritten in terms of multiples of the sampling frequency $f = k f_s/N$, becoming the \gls{DFT}
 \begin{equation*}
 	\label{eq:fourier:dft}
 	\phantom{.}
-	X(k) = e^{ -i 2 \pi t[0]} \sum_{n=0}^{N-1}   x[n]\, \cdot e^{ -i 2 \pi \frac{k n}{N} }
+	X(k)
+	% = \sum_{n=0}^{N-1}   x(t[n])\, e^{ -i 2 \pi f (t[0] + n/f_s)}
+	% = \sum_{n=0}^{N-1}   x(t[n])\, e^{ -i 2 \pi f t[0]}\, e^{ -i 2 \pi f n/f_s}
+	% = e^{ -i 2 \pi f t[0]}\, \sum_{n=0}^{N-1}   x(t[n])\, e^{ -i 2 \pi k n}
+	= e^{ -i 2 \pi f t[0]} \sum_{n=0}^{N-1}   x(t[n])\, \cdot e^{ -i 2 \pi \frac{k n}{N} }
 	.
 \end{equation*}
 
 The direct computation of this transform takes $2N$ complex multiplications and $2(N-1)$ complex additions for a single frequency $k$.
 When computing this transform for all integer $0 \leq k < N$, this amounts to $\mathcal{O}(N^2)$ complex computations.
-\acrlong{FFT}s (\gls{FFT}s) are efficient algorithms that derive all $X( 0 \leq k < N)$ in $\mathcal{O}( N \log N)$ calculations.
+\acrlong{FFT}s (\acrshort{FFT}s) are efficient algorithms that derive all $X( 0 \leq k < N)$ in $\mathcal{O}( N \log N)$ calculations.
 \Todo{citation?}
 %For integer $0 \leq k < N $, efficient algorithms exist that derive all $X( 0 \leq k < N )$ in $\mathcal{O}( N \log N )$ calculations instead of $\mathcal{O}(kcalled \acrlong{FFT}s, sampling a subset of the frequencies.\Todo{citation?}
 
-
 \begin{figure}
-	\includegraphics[width=\textwidth]{fourier/dtft_dft_comparison.pdf}
+	\begin{subfigure}{0.45\textwidth}
+		\includegraphics[width=\textwidth]{methods/fourier/waveform.pdf}%
+		%\caption{}
+	\end{subfigure}
+	\hfill
+	\begin{subfigure}{0.45\textwidth}
+		\includegraphics[width=\textwidth]{methods/fourier/noisy_spectrum.pdf}%
+		\label{fig:fourier:dtft_dft}
+		%\caption{}
+	\end{subfigure}
 	\caption{
+		Left: A waveform sampling a sine wave with white noise.
+		Right:
+			The frequency spectrum of the waveform.
 			Comparison of the \gls{DTFT} and \gls{DFT} of the same waveform.
 			The \gls{DFT} can be interpreted as sampling the \gls{DTFT} at integer multiple of the waveform's sampling rate $f_s$.
+		\Todo{Larger labels, fix spectrum plot}
 	}
-	\label{fig:fourier:dtft_dft}
 \end{figure}
 
 \bigskip
@@ -166,8 +179,8 @@ i.e.,~\eqref{eq:fourier:dtft} becomes
 		%\\ &
 		\equiv \Re(X(f)) + i \Im(X(f))
 		\\ &
-		=     \sum_{n=0}^{N-1} \, x[n] \, \cos( 2\pi f t[n] )
+		=     \sum_{n=0}^{N-1} \, x(t[n]) \, \cos( 2\pi f t[n] )
-		  - i \sum_{n=0}^{N-1} \, x[n] \, \sin( 2\pi f t[n] )
+		  - i \sum_{n=0}^{N-1} \, x(t[n]) \, \sin( 2\pi f t[n] )
 		.
 	\end{aligned}
 \end{equation}
@@ -194,7 +207,7 @@ Likewise, the complex phase at a given frequency $\pTrue(f)$ is obtained by
 \\
 
 % Recover A\cos(2\pi t[n] f + \phi) using above definitions
-Applying \eqref{eq:fourier:dtft_decomposed} to a signal $x(t) = A\cos(2\pi t[n] f + \pTrue)$ with the above definitions obtains
+Applying \eqref{eq:fourier:dtft_decomposed} to a signal $x(t) = A\cos(2\pi t f + \pTrue)$ with the above definitions obtains
 an amplitude $A$ and phase $\pTrue$ at frequency $f$.
 When the minus sign in the exponent of \eqref{eq:fourier} is not taken into account, the calculated phase in \eqref{eq:complex_phase} will have an extra minus sign.
 
@@ -213,9 +226,8 @@ opening the way to efficiently measuring the phases in realtime.\Todo{figure?}
 
 \section{Cross-Correlation}% <<<<
 \label{sec:correlation}
-\Todo{intro}
 The cross-correlation is a measure of how similar two waveforms $u(t)$ and $v(t)$ are.
-By introducing a time delay $\tau$ in one of the waveforms it is turned into a function of this time delay.
+By introducing a time delay $\tau$ in one of the waveforms it turns into a function of this time delay.
 
 It is defined as
 \begin{equation}
@@ -232,39 +244,42 @@ Still, $\tau$ remains a continuous variable.
 
 % Discrete \tau because of sampling
 In reality, both waveforms have a finite size, also reducing the time delay $\tau$ resolution to the highest sampling rate of the two waveforms.
-When the sampling rates are equal, the time delay variable is in effect shifting one waveform by some number of samples.
+When the sampling rates are equal, the time delay variable is effectively shifting one waveform by a number of samples.
+\\
+% Upsampling? No
+Techniques such as upsampling or interpolation can be used to effectively change the sampling rate of a waveform up to a certain degree.
+However, for the purpose in this document, these methods are not used.
 \\
 
-% Approaching analog \tau; or applying upsampling and interpolation
+% Approaching analog \tau; or zero-stuffing
-Techniques such as upsampling or interpolation can be used 
+Since zero-valued samples do not contribute to the integral of \eqref{eq:correlation_cont}, they can be freely added (or ignored) to a waveform when performing the calculations.
-When the sampling rates are 
+This means two waveforms of different sampling rates can be correlated when the sampling rates are integer multiples of each other, simply by zero-stuffing the slowly sampled waveform.
+This allows for approximating an analog time delay between two waveforms when one waveform is sampled at a very high rate as compared to the other.
+
+\Todo{resolution 1/sqrt(12)?}
+
 
 \begin{figure}
-	\begin{subfigure}{\textwidth}
+	\centering
-		\includegraphics[width=\textwidth]{pulse/waveform_12_correlation.pdf}
-		\caption{
-			Correlation of two Waveforms as a function of time.
-		}%
-		\label{subfig:correlation}
-	\end{subfigure}%
-	\\
 	\begin{subfigure}{0.45\textwidth}
-		\includegraphics[width=\textwidth]{pulse/waveform_1.pdf}
+		\includegraphics[width=\textwidth]{methods/correlation/waveforms.pdf}
-		\caption{
+		%\caption{
-			Waveform 1
+		%	Two waveforms.
-		}
+		%}%
-		\label{}
+		\label{subfig:correlation:waveforms}
 	\end{subfigure}
 	\hfill
 	\begin{subfigure}{0.45\textwidth}
-		\includegraphics[width=\textwidth]{pulse/waveform_2.pdf}
+		\includegraphics[width=\textwidth]{methods/correlation/correlation.pdf}
+		%\caption{
+		%	The correlation of two Waveforms as a function of time.
+		%}%
+		\label{subfig:correlation}
+	\end{subfigure}%
 	\caption{
-			Waveform 2
+		Left: Two waveforms to be correlated.
-		}
+		Right: The correlation of both waveforms as a function of the time delay $\tau$.
-		\label{}
+		Here the best time delay (red dashed line) is found at $5$, which would align the maximum amplitudes of both waveforms in the left pane.
-	\end{subfigure}
-	\caption{
-		Top: Correlation of Waveform 1 and Waveform 2
 	}
 	\label{fig:correlation}
 \end{figure}
@@ -289,8 +304,10 @@ The Hilbert Transform corresponds to a \gls{FT} where positive frequencies $f >
 The envelope of a waveform $x(t)$ is determined by taking the absolute value of its analytic signal $s_a(t)$.
 Figure~\ref{fig:hilbert_transform} shows an envelope with its original waveform.
 
+
 \begin{figure}
-	\includegraphics[width=\textwidth]{pulse/hilbert_timing_interpolation_template.pdf}
+	\centering
+	\includegraphics[width=0.5\textwidth]{pulse/hilbert_timing_interpolation_template.pdf}
 	\caption{
 		Timing information from the maximum amplitude of the envelope.
 	}