m-thesis-introduction/airshower_beacon_simulation/Makefile

88 lines
2.6 KiB
Makefile
Raw Permalink Normal View History

2022-09-28 15:18:04 +02:00
.PHONY: all
FIG_DIR ?= ./figures
-include config.mk
2022-09-28 15:18:04 +02:00
MAX_K ?= 3
CLK_DEV ?= 20
TRACE_N ?= 4096
TRACE_PRE ?= 500
NOISE_SIGMA ?= 1e4
BEAC_AMP ?= 1e3 0 0
BEAC_F ?= 51.53e-3
BEAC_DECAY ?= 0
PB_LOW ?= 0.03
PB_HIGH ?= 0.08
REF_ANTS ?=
2022-09-28 15:18:04 +02:00
N_MASK ?= 500
DATA_DIR ?= ./data
INPUT_DIR ?= ./ZH_airshower/
2023-02-02 18:09:10 +01:00
SEED ?= 12345
all: beacon clocks phases findks vary-fixes reconstruct
2022-09-28 15:18:04 +02:00
2023-02-14 16:32:25 +01:00
beacon: generate-beacon signal-to-noise
phases: beacon-phase clock-phase baseline-phase antenna-phase
######
generate-beacon:
./aa_generate_beacon.py -N ${TRACE_N} -P ${TRACE_PRE} -n ${NOISE_SIGMA} -a ${BEAC_AMP} -f ${BEAC_F} -l ${PB_LOW} -u ${PB_HIGH} -d ${BEAC_DECAY} --data-dir ${DATA_DIR} --input-fname ${INPUT_DIR} | tee ${FIG_DIR}/aa.log
./ab_modify_clocks.py 0 --no-save-clocks --data-dir ${DATA_DIR} | tee ${FIG_DIR}/ab.log
2023-02-14 16:32:25 +01:00
signal-to-noise:
./ac_show_signal_to_noise.py -l ${PB_LOW} -u ${PB_HIGH} --no-show-plots --fig-dir=${FIG_DIR} --data-dir ${DATA_DIR}
./view_beaconed_antenna.py 72 -p x -p y -p z -p n -p b --ft --no-show-plots --fig-dir=${FIG_DIR} --data-dir ${DATA_DIR}
2022-09-28 15:18:04 +02:00
2023-02-14 16:32:25 +01:00
#
new-clocks:
2023-02-02 18:09:10 +01:00
./ab_modify_clocks.py ${CLK_DEV} --seed ${SEED} --gaussian --data-dir ${DATA_DIR}
2022-09-28 15:18:04 +02:00
clocks:
./ab_modify_clocks.py ${CLK_DEV} --read-clocks-file --seed ${SEED} --gaussian --data-dir ${DATA_DIR}
reset-clocks:
./ab_modify_clocks.py 0 --data-dir ${DATA_DIR}
2023-02-14 16:32:25 +01:00
#
beacon-phase:
./ba_measure_beacon_phase.py --N-mask ${N_MASK} --no-show-plots --fig-dir=${FIG_DIR} --data-dir ${DATA_DIR}
2023-02-14 16:32:25 +01:00
clock-phase:
./bb_measure_clock_phase.py --no-show-plots --fig-dir=${FIG_DIR} --data-dir ${DATA_DIR}
2023-02-14 16:32:25 +01:00
baseline-phase:
./bc_baseline_phase_deltas.py ${REF_ANTS} --no-show-plots --fig-dir=${FIG_DIR} --data-dir ${DATA_DIR}
2023-02-14 16:32:25 +01:00
antenna-phase:
./bd_antenna_phase_deltas.py --no-show-plots --fig-dir=${FIG_DIR} --data-dir ${DATA_DIR}
2023-02-14 16:32:25 +01:00
#
findks:
2023-02-02 19:27:01 +01:00
./ca_period_from_shower.py --input-fname ${INPUT_DIR} --max-k ${MAX_K} --no-show-plots --fig-dir=${FIG_DIR} --data-dir ${DATA_DIR} -l ${PB_LOW} -u ${PB_HIGH}
rough-findks:
./ca_period_from_shower.py --input-fname ${INPUT_DIR} --max-k ${MAX_K} --no-show-plots --fig-dir=${FIG_DIR} --data-dir ${DATA_DIR} -l ${PB_LOW} -u ${PB_HIGH} --quick_run
reportks:
./cb_report_measured_antenna_time_offsets.py --no-show-plots --fig-dir=${FIG_DIR} --data-dir ${DATA_DIR}
2023-02-14 16:32:25 +01:00
#
vary-fixes:
./dc_grid_power_time_fixes.py --no-show-plots --fig-dir=${FIG_DIR} --data-dir ${DATA_DIR} --input-fname ${INPUT_DIR}
2023-02-14 16:32:25 +01:00
#
reconstruct:
./da_reconstruction.py --no-show-plots --fig-dir=${FIG_DIR} --data-dir ${DATA_DIR} --input-fname ${INPUT_DIR} --clock-repair full
./db_longitudinal_figure.py --no-show-plots --fig-dir=${FIG_DIR} --data-dir ${DATA_DIR} --clock-repair full
2022-09-28 15:18:04 +02:00
dist-clean:
2023-02-14 16:32:25 +01:00
rm -vf ${DATA_DIR}/
rm -vf ${FIG_DIR}/